Menu

LONRIHEAT APPLICATIONS

Electric Underfloor Heating

Select heating cables or mats around floor construction, usable heated area and thermostat placement.

Bathroom threshold with a visible electric heating mat and separate floor-sensor conduit
Application illustration; not a photograph documenting a LONRIHEAT installation.
Commercial BuildingsResidential

Application and low-temperature risk

Room comfort and floor-surface conditions depend on the complete floor build-up and intended heating role.

Equipment or areas to review

Net heated area excluding permanent fixtures, floor layers and finish, heat-loss/design duty, mat/cable layout, supply, thermostat, floor sensor and wet-area requirements. Identify each heated zone and the unheated interfaces.

Define the design objective

Distinguish freeze protection, temperature maintenance, heat-up and anti-condensation. State the required condition and operating schedule; each duty needs its own heat balance and acceptance basis.

Compare heating technologies

Compare loose heating cable with factory-prelaid heating mats against floor construction, available area, installation geometry and control requirements.

Product selection scope

Use the linked product families to compare construction, interfaces and configuration-specific documents. Final model, supply, output, length, temperature limits and accessories must match the proposal.

Controls and sensing

Define sensor location/type, controller logic, zones, startup/load current, protection, alarms and any independent limiter. Agree integration and monitoring responsibilities.

Electrical, environmental and area requirements

Specify destination market, electrical supply, moisture/corrosion, mechanical exposure and any hazardous-area or system-specific approval requirements. Verify the exact configuration and document scope; no site approval is inferred.

Installation structure

Coordinate the cable or mat layout with the floor/pavement layers, fixing, sensor conduit, joints, cold leads and installation sequence. Do not cut a heating conductor or infer permissible spacing from a photograph.

Design input parameters

Net heated area excluding permanent fixtures, floor layers and finish, heat-loss/design duty, mat/cable layout, supply, thermostat, floor sensor and wet-area requirements.

Testing and delivery evidence

Request the proposed data sheet, layout/dimension drawing, wiring and control diagram, installation instructions, component schedule and applicable test or compliance documents. Agree document revision, commissioning records, acceptance criteria and responsibility.

Common purchasing errors

Do not select from nominal W/m alone, treat maximum exposure as maintain temperature, mix configuration limits, omit cold points or substitute one component approval for complete system evidence.

Relevant product families

LONRIHEAT Electric floor heating cables and mats — company-supplied product photographLONRIHEAT Floor heating cablesA product-family entry for residential and commercial floor-heating enquiries. Floor construction, area, power and controls determine the design.Representative factory-prelaid cable-mat form. The offered underfloor assembly, dimensions, electrical data and floor suitability are specified separately.LONRIHEAT Factory-prelaid underfloor heating matsFactory-prelaid heating mats for electric underfloor-heating projects. Define net heated area, floor construction, supply and controls before specifying the mat layout.

Related answers, products & documents

revision
MARKET-APPLICATIONS-20261119-V1
updated
2026-11-19

Industry pathway: Commercial buildings →

Additional application details

Problem and design purpose

Match the cable/mat to floor build-up and heating role.

Required inputs

Heated area excluding fixed furniture, floor covering, insulation, screed, supply, thermostat and sensor.

System architecture

Define heater, supply/protection, controls/sensors, terminations, fixing, insulation and access.

Risks and limitations

Check surface temperature and covering limits; never infer one spacing for every floor.

Verification and handover

Retain the selected configuration, conditioned output/limits, accessory schedule, drawing, installation/test plan and destination-market documents. Agree open inputs and responsibility.

Buyer review checklist

Can electric heating cable be used for underfloor heating? When should I choose a heating cable, mesh mat or aluminium foil mat?

See how the heating fits the application

1 Floor finish
2 Approved embedding layer
3 Cable / mat + floor sensor
4 Subfloor / insulation
Installation / configuration principle. Place the floor sensor between adjacent heating runs. Floor materials, spacing, embedding and movement joints follow the approved system instructions.

Review the installation arrangement

Electric floor heating
Installation context illustration; confirm the selected assembly and engineer-approved layout.

Review the physical product and interfaces

These supplied product photographs show physical examples. Application suitability, exact specifications and compliance remain specific to the offered configuration.

LONRIHEAT Twin-conductor floor heating cable — company-supplied product photograph
Supplied product photograph
Company-supplied representative product photograph. Original colours, plug and fitting geometry retained. Confirm the exact order configuration.
LONRIHEAT Twin-conductor floor heating cable →
Red cable and black cold-lead detail
Supplied product detail
User-supplied product photograph. Original product pixels preserved; exact order configuration is confirmed with the specification.
Review the complete product configuration →
Representative factory-prelaid cable-mat form. The offered underfloor assembly, dimensions, electrical data and floor suitability are specified separately.
Supplied product photograph
Representative factory-prelaid cable-mat form. The offered underfloor assembly, dimensions, electrical data and floor suitability are specified separately.
LONRIHEAT Factory-prelaid underfloor heating mats →
Representative factory-prelaid cable-mat form. The offered underfloor assembly, dimensions, electrical data and floor suitability are specified separately.
Supplied product detail
Representative factory-prelaid cable-mat form. The offered underfloor assembly, dimensions, electrical data and floor suitability are specified separately.
Review the complete product configuration →

RFQ technical information

Share what is known and identify missing inputs. Submission requests a technical review; it does not establish a final design or approval.

Application / equipment
Describe the duty and attach a drawing
Design conditions
Net heated area excluding permanent fixtures, floor layers and finish, heat-loss/design duty, mat/cable layout, supply, thermostat, floor sensor and wet-area requirements.
Supply / control
Voltage/frequency, zones, sensor/controller and protection
Commercial / evidence
Company, email, quantity, destination, timing and required documents

Application FAQ

Can this application be selected from one temperature or power figure?

Define the complete design basis and interfaces first. Maintain temperature, exposure conditions, supply, geometry, insulation and controls must be assessed together.

Do the linked products prove approval for this application?

No. Verify the proposed model and complete configuration against its documents and the destination requirements. A product-family link is a selection path, not an application approval.

What should I send for engineering review?

Net heated area excluding permanent fixtures, floor layers and finish, heat-loss/design duty, mat/cable layout, supply, thermostat, floor sensor and wet-area requirements. Include drawings/photos, quantity, destination and the requested deliverables; mark unknown inputs.

Get selection or project review

Results from preliminary tools are for reference and recommendations only. Final quantities and specifications must follow the engineer-approved design.

Open the preliminary quantity estimator · Contact the export team